GFCI Code-Required • 20A & 240V Options • Workbench & EV Circuits • Licensed • (239) 888-8888
Garages are among the most under-served electrical spaces in Southwest Florida homes. Many homes have only one or two outlets installed during original construction — far fewer than needed for tools, refrigerators, EV chargers, air compressors, and general workshop use. The NEC requires all garage outlets to be GFCI-protected (125V receptacles) and recommends 20A circuits for workshop use. ElectriciansX adds garage outlets, dedicated workshop circuits, and 240V circuits for air compressors, welders, and EV chargers throughout Southwest Florida.
Fort Myers is the commercial and residential hub of Lee County, with housing stock ranging from older downtown neighborhoods to new construction in Gateway, Daniels Corridor, and Colonial Boulevard communities. Whether your garage is a workspace, a storage area, or you’re converting it into a multi-use space, ElectriciansX handles all garage electrical work in Lee County — from a single additional GFCI outlet to a full workshop panel with multiple 20A and 240V circuits.
From a single GFCI outlet to a full workshop sub-panel — we handle all garage electrical work.
Add one or more 20A GFCI-protected outlets along garage walls. The NEC requires GFCI protection for all 125V garage outlets — we install code-compliant outlets with proper in-use covers.
Air compressors, table saws, welders, and other heavy shop tools often require 240V power. We install NEMA 6-20, 6-30, or 6-50 outlets for your specific equipment.
A garage NEMA 14-50 outlet or Level 2 EVSE circuit lets you charge your electric vehicle overnight at home. We install and permit EV charger circuits for all makes and models.
A workbench outlet package typically includes 2–4 outlets along the bench wall, task lighting above the bench, and a dedicated 20A circuit separate from existing garage circuits.
A dedicated 20A circuit for a garage refrigerator or chest freezer prevents nuisance tripping when the compressor starts and protects food from power-sharing issues.
For workshops with multiple heavy circuits, a dedicated sub-panel in the garage is the right solution. We install 60A–100A sub-panels with multiple breaker slots for all your shop circuits.
We verify that your main panel has available capacity for new garage circuits and identify the best route for running new wire to the garage.
We work with you to place outlets at the right height and spacing for your intended use — workbench, tool storage wall, EV parking spot, or refrigerator location.
We run 12 AWG (20A) or appropriately sized wire from the panel to the garage, routing through attic, crawl space, or conduit along exterior walls as needed.
All garage 125V outlets are installed with GFCI protection — either GFCI outlets or a GFCI breaker protecting the entire circuit. 240V outlets are installed per NEC requirements.
We pull the permit for new circuits, pass the electrical inspection, and test every outlet before declaring the job complete.
Click another city to see local service details.
Yes. Florida follows the NEC, which requires GFCI protection for all 125V, 15A and 20A receptacles in garages — both attached and detached. This applies to new outlet installations and to replacement outlets during renovation work. 240V outlets for tools and EV chargers are not subject to the GFCI requirement but must meet other applicable NEC sections.
A standard garage circuit is 20A (12 AWG wire) — suitable for general-purpose outlets, a garage refrigerator, and most hand tools. A dedicated 20A circuit for a refrigerator or freezer is recommended to prevent nuisance tripping. Air compressors, welders, and table saws may require dedicated 240V circuits. EV chargers typically need a 50A circuit. We assess your needs and plan circuits accordingly.
A single new 20A GFCI outlet added to an existing garage circuit typically runs $150–$250. Running a new dedicated circuit from the panel to the garage for additional outlets runs $300–$600+ depending on panel location and routing distance. Dedicated 240V circuits for tools or EV chargers range from $400–$900. We provide detailed, upfront estimates.
Yes — we install 240V outlets in any configuration needed for garage tools: NEMA 6-20 (20A) for smaller compressors and tools, NEMA 6-30 (30A) for larger compressors, and NEMA 6-50 (50A) for welders and plasma cutters. We size the circuit and outlet to match your specific equipment’s nameplate requirements.
The NEC requires at least one outlet for a single-car garage and at least two for a multi-car garage as a minimum — but most homeowners find 4–6 outlets or more are needed for practical use. A workshop-grade garage with tools, a refrigerator, and EV charging may need 8–12 outlets across multiple circuits. We plan the layout based on your intended use.
Yes — adding new circuits or new outlet locations in a garage requires an electrical permit in all Southwest Florida jurisdictions. Replacing an existing outlet with a GFCI outlet in the same location typically does not require a permit. ElectriciansX handles all permit applications and inspections for new circuit work.
